Not every line that needs a variable barcode needs an industrial print and apply head.
The Altech ALcode LT is the economical member of the ALcode print and apply family. Like the industrial ALcode, it prints a label at the moment it is applied, so the barcode can carry a lot code, a batch, a date, a weight or a serial number that changes with every pack.
Marapack Services is the Pacific Northwest distributor for Altech labeling systems, importing direct from the factory in Bareggio, Italy, and print and apply is the core of what we install and service. Marapack Services is an independent company, not Altech S.r.l. and not ALTech US.
Deciding between the ALcode LT and the industrial head? Book an equipment audit and we will measure the line before either one is quoted.
What is the Altech ALcode LT?
The Altech ALcode LT, price list code CD06, is the economical print and apply head in Altech's ALcode family. It prints each label as it applies it, so variable data such as a lot code, a date, a GTIN or a serial number goes on the pack in one step.
It does the same fundamental job as the CD20. Altech positions the CD20 as the industrial head and the CD06 as the economical one, and the two differ in speed, label width and print engine (see the table below). That makes the LT the head to price first when a line needs print and apply but the business case for the industrial head is not obvious.
Should you choose the ALcode LT or the industrial ALcode?
Choose between the ALcode LT and the industrial ALcode on the line walk, from your case rate, your label, your print engine and how many hours the line runs. Altech rates the LT at up to 40 labels a minute with a 104 mm label, and the industrial ALcode at up to 100 labels a minute with labels to 180 mm.
| ALcode LT (CD06) | ALcode (CD20) | |
|---|---|---|
| Position in the family | The economical, compact head for low to medium volume | The industrial head for 24/7 line critical work. Also written CD-20 in order paperwork |
| Production speed | Up to 40 labels/min | Up to 100 labels/min |
| Maximum label width | 104 mm (about 4.1 in) leading edge, 112 mm (about 4.4 in) including liner | 180 mm (about 7.1 in) with a SATO engine |
| Print engine | SATO LT408, 203 dpi, 150 mm/s (6 in/s) | SATO S84-86 or Zebra ZE500 |
| Label roll | 220 mm (about 8.7 in) maximum | 300 mm (about 11.8 in), 400 mm option |
| Air | 5 bar (about 73 psi), 50 l/min | 5 bar (about 73 psi), 50 l/min |
Both speed figures depend on label size and applicator, as Altech states them. The full bill of materials for the industrial version is on our page for the ALcode industrial head. The LT is the one to price first when budget is the constraint, and the site visit confirms whether it suits the line.
Figures are from Altech's ALcode LT specification page and ALcode specification page.
What the LT is not. Altech built it around the lighter SATO LT engine for low to medium volume. If the line runs round the clock at case rates above about 40 a minute, the industrial head is the honest answer.
How Altech names it
Altech's price list carries this as CD06, family name ALcode LT. The code is the identifier that never changes and it is what any parts quote is written against.
SX and DX on Altech paperwork are the Italian abbreviations for left hand and right hand. They appear in factory serial records, and handing is specified when the machine is ordered: it sets which side of the conveyor the head mounts on and which way the web runs.
Already own one? Send the serial number and the Commessa number from the machine plate. Factory parts quotes are keyed to those two numbers rather than to a model name, and Altech maintains a 3D viewer per machine for part lookup.
What is the ALcode LT used for?
The ALcode LT is used where the label data changes per pack but the line does not justify the industrial head: moderate volume lines, seasonal and secondary lines, smaller pack houses with a retail barcode requirement, a second labeling point beside an industrial head, and replacing a desktop printer with somebody applying labels by hand.
- Variable data on a moderate volume line. Lot codes, batch numbers, dates, weights, counts, GTINs and serial codes that change per pack
- Seasonal and secondary lines that need proper print and apply during a window rather than year round
- Smaller pack houses and processors that have a retail customer barcode requirement but not a case line running at production speed
- A second labeling point on a line that already has an industrial head elsewhere
- Replacing a manual print station that consists of a desktop printer and somebody applying labels by hand
If the label content never changes, you do not need print and apply at all. A labeling head such as the Altech ALstep or ALritma is cheaper and simpler.
What does an ALcode LT need around it?
An ALcode LT needs its print engine, a data interface to wherever your lot codes live, an applicator matched to the product face, conveying that presents the product consistently, and label sensing. Print and apply is a system rather than a box, and the applicator decides whether the label lands.
Print engine. The ALcode LT is built around one engine: the SATO LT408 thermal transfer module (CD40), at 203 dpi and 150 mm/s. Altech designed the LT specifically for it, as a lighter version of the SATO S84 engine used in the industrial ALcode. The SATO S84 and S86 engines (TX42, TX43, TX46, TX62, TX63) belong to the industrial head, not the LT. Altech's price list also carries an ST40 assembly for integrating the LT408 into an Altech head; confirm on your quote whether your build needs it.
Interfaces. RS232C, parallel, USB, RS422 and RS485, LAN and wireless, because a print and apply head is only useful if it can be fed data from wherever your lot codes actually live.
Applicators. Altech offers the LT with five application methods: air blast, for non-contact labeling on uneven surfaces at up to 80 mm (about 3.1 in) from the product and more than 40 units a minute, depending on label size; tamp blow, where a piston carries the label close to the product and blows it on; tamp by contact, for still products or recessed areas; a multiformat swinging plate, for moving products of varying size; and a rotary arm, for front or back labeling (listed on Altech UK's LT page; Altech's ALcode brochure does not list it for the LT). The applicator, not the head, is what decides whether the label lands.
Conveying and presentation. Altech ALbelt compact, single, flighted and two section conveyors, spacers and gapping units, timing screws and stabilizing belts.
Sensing options. Altech's price list carries the standard label sensor, the CE06 label tracing sensor for transparent product, label presence check, laser scanner, mark reader, and the smart camera options for over print reading and label presence, all as equipment line items quoted with the machine. Altech's ALcode brochure lists none of its scanner or sensor options for the LT, so confirm which ones a CD06 build takes.
For how the LT fits among other print and apply formats, see our overview of label printer applicators.
Can the ALcode LT handle PTI labels on a smaller produce line?
It has the right architecture for one. A Produce Traceability Initiative case label needs a GS1-128 barcode carrying the GTIN and lot, and the ALcode LT is a print and apply head taking a thermal transfer print engine, so it can print that label as the case is labeled. Whether it suits your line comes down to rate, label size and case surface.
A packer that needs a PTI case label for one retail customer, on one line, for a season that runs a few weeks, is badly served by a quote for an industrial system and equally badly served by a desktop printer and a roll of labels. The LT is worth pricing in that gap.
The label requirements do not change with the size of the operation. A PTI case label still needs a GS1-128 barcode carrying the GTIN and lot, still needs to be readable at the receiving dock, and still needs the print quality grade the standard asks for. What changes is how much machine you need behind it.
Who services the ALcode LT and its print engine?
Marapack Services services the ALcode LT and the print engine inside it. We stock parts for Altech, PackLeader, some Label-Aire and Tach-It machines, and we service Altech, Label-Aire 3100 applicators and 5100 systems, PackLeader, CTM and Tach-It equipment. When a print engine wears out, we manage the rebuild.
Our page on SATO print engine repair covers the engine side. Wear parts and the ordering route are on our page of ALcode LT spare parts, quoted against your machine serial number and Commessa.
Frequently asked questions
How much slower is the ALcode LT than the ALcode? On Altech's published figures, the LT runs up to 40 labels a minute and the industrial ALcode up to 100, both depending on label size and applicator. Give us your case rate and your label size and we will tell you which side of that line you sit on.
Can we upgrade to a CD20 later? The head is the head, so an upgrade is a new head rather than a conversion. The stand, conveyor and sensing may carry over; do not assume the applicator does, because Altech redesigned the LT's application systems for its compact body. That changes the economics of the decision. Worth asking before you buy rather than after.
We already have one and it is missing labels intermittently. Check the sensor, the peeler bar, web tension and the air supply, in that order, before the printer. Our label applicator troubleshooting guide walks through those checks; or call us before the season starts rather than during it.
How much does an ALcode LT cost? The price is set by the head, the print engine, the interface, the applicator, the sensing and the conveying around it. We quote after the line assessment, because a print and apply price without a specification behind it misleads both ways.
Get the size of the machine right the first time
The expensive mistake in print and apply is not buying the wrong brand, it is buying the wrong size of system for the line. Too much machine wastes capital. Too little machine becomes the bottleneck in the weeks you can least afford one.
We walk the line, measure the rate and the labels, and tell you which head your line actually needs, including when the answer is that you do not need print and apply at all. Call 253-709-5566 or get the LT or CD20 question settled on site.
